ANSI cut level A4HPPE outer layer combined with warm 7 gauge acrylic liner. Tested for both cut and heat protection. Flexible sandy nitrile coating. Features: ● ANSI cut level A4 ● Flexible sandy nitrile coating offers great grip in wet and dry conditions ● Provides over 650°F contact heat protection ● Specially designed for use in cold conditions ● Warm 7 gauge acrylic liner for extreme cold protection ● Level D cut resistance ● 7 gauge liner for dexterity ● Available in sizes up to 3XL ● Double dipped coating for durabilityOVERVIEW
- Max-Dri™ Moisture Wicking mesh in Hi-Viz Green or Hi-Viz Orange
- Available with either long or short sleeves
- 2” heat transfer reflective tape
- One upper left front pocket
- Collar with two buttons
- Meets ANSI/ISEA 107-2010 Standards
- Available in sizes M, L, XL, 2XL, 3XL, 4XL and 5XL
- Sale!
OVERVIEW
Designed to deliver comfort, warmth, and durability during marine operations, the MJ6214 T1 Classic Flotation Bomber Jacket's closed-cell foam insulation will provide flotation and in-water insulation to delay the onset of hypothermia in the event of water immersion. Coupled with functional design elements such as fleece-lined pockets and a storm flap, Mustang Survival's MJ6214 T1 Classic Flotation Bomber Jacket adds up to an unbeatable value. The MJ6214 T1 Version includes SOLAS reflective tape across the chest and around each wrist to provide increased visibility. Suitable for the requirements of Industrial, Regulatory, and Military environments, the Classic Flotation Bomber Jacket is a standard piece of uniform for many government agencies, as well as everyday recreational activities such as boating, fishing or sailing.- Relaxed fit for mobility and comfort
- 62 square inch of reflective tape
- Neoprene wrist seals
- Pen pocket on right sleeve
- 4 front pockets
- 1 large pocket on the inside of the jacket
- Full-length storm-flap
- Internal waist belt to reduce ride-up
- Fleece-lined front pockets
Small:- Chest 34" - 38"
- Waist 28" - 30"
- Length 27.5"
- Chest 38" - 42"
- Waist 32" - 34"
- Length 31"
- Chest 42" - 46"
- Waist 36" - 38"
- Length 32"
- Chest 46" - 50"
- Waist 40" - 42"
- Length 33"
- Chest 50" - 54"
- Waist 44" - 46"
- Length 34"
- Chest 54" - 58"
- Waist 48" - 50"
- Length 35"
Approval: USCG - UL1123 - Marine Buoyant Devices 160.064 - Type III - Sale!
OVERVIEW
Hazards on job sites that operate in cold weather are increased as the temperature dips, leading to the need for protective gloves with excellent grip and insulation.- MicroSable Interior Lining: Adds insulation and resists pilling for added comfort and longevity.
- Flexible TPR: Protects fingers, thumb, back of hand and knuckles from cuts and scrapes, while providing time to pull hand out of glove if caught in machinery.
- Long-Cuff Design: Adds protection, comfort and “tear-away” ability if caught in heavy machinery.
- One-piece Palm with Kevlar Thread Stitching: Adds durability and longevity.
- SkidX Grip: Adds oil, water, and petro-chemical resistance, as well as heightened gripping power for wet, oily or dry surfaces.
- Available in sizes: Small-4XL
OVERVIEW
- Foam padded rope control channel on palm
- Premium synthetic leather palm and fingertip patches
- Heavy duty leather material between fingers for extra durability
- Incredible fingertip dexterity allows knot untying without removing gloves
- Secured cuff closure with hook and loop TPR pull tab closure
- Reflective markings on top of hand for better visibility
- Kevlar stitching
- Available in black or red
OVERVIEW
- TPR impact protection on top of hand and full length of fingers
- 6mm integrated knuckle design for flexible protection
- Waterproof and breathable Hipora barrier to protect hands from micro-organisms such as TB, Hepatitis, Staph and HIV
- Meets O.S.H.A. Standards for Blood-borne Pathogen Protection (29CFR 1910.1030)
- Elastic cuff and gaiter to keep out glass and debris
- Boxed finger tip design for better fit and comfort
- Cut resistant KevLoc palm, thumb panels, and side panels
- Reflective markings for increased visibility
- Sale!The moment they arrive at a fire, firefighters are exposed to microscopic carcinogenic particles. We all know that breathing these cancer-causing particulates is dangerous. But studies now show that absorbing them through the skin is just as bad. Traditional hoods are designed to protect against heat, not carcinogenic particles. Today’s particulate-blocking hoods are vital for firefighter health and safety. Our new INNOTEX® GRAY™ Hood 25 Nano – not made with PFAS – offers complete coverage protection against toxic particulates. Made with DuPont™ Nomex® Nano Flex, this light & flexible 1-layer hood features a nanofiber-based particulate barrier that stops particulates at 99.8%. Its remarkable breathability & high thermal heat loss value ensure unbeatable comfort in any situation. Available in Medium/Large (Most Common Size) or XL
- Sale!
OVERVIEW
- One-Piece, 3D, Direct-Injected Thermoplastic Rubber: adds impact protection for entire back of hand and fingers, with elevated knuckles.
- One-Piece Palm with Kevlar® Stitching: adds durability and longevity.
- TefSecure Silicone Grip Grid: adds oil, water and petro-chemical resistance, and grip control.
- Long-Cuff Design: adds protection, comfort and "tear-away" ability with heavy machinery.
- Curved Fingers: matches natural contour of hand for less hand strain.
- Easy-Pull Tabs: allows user to add name to glove, and easily pull glove on.
- Available Sizes: Small-4XL
OVERVIEW
- Flexible TPR impact protection on knuckles and fingers
- (R-314) High visibility for increased safety, Reflective markings for increased visibility
- CE rated for EN388 level 2 cut and puncture resistance
- KevLoc grip system on palm & fingers enhances grip
- Extended cuff with gaiter closure to keep out debris
- Available in either black or yellow
- Kevlar stitched palm with padding
- Sale!
OVERVIEW
Lakeland Interceptor Plus, Level A suits are gas tight and are the ultimate line of chemical protection. INT640B front entry suits are configured with gloves, boots, face shield, and heat-sealed seams. Available in sizes SM-5X, these protective suits are ideal when the maximum level of chemical protection is needed, like emergency response and HazMat operations. Available in small, medium, large, XL, 2XL, 3XL and 4XL (Sizing is based upon height and weight - please contact us for information to properly size your suit) Please note this is an updated version of prior model 80640. - Sale!
OVERVIEW
- Premium EVA foam palm pad to dampen shock and impact
- Abrasion resistant, textured PVC on palm and fingers
- Breathable, 3-layer stretch spandex with neoprene knuckle pad
- Synthetic leather palm and fingers
- Terry thumb brow wipe
- Flex zones for added comfort
- Reinforced fingertips for optimal durability
- Full-finger design
- Sizes: Small, Medium, Large, XL or 2XL
- Sale!
OVERVIEW
The INNOTEX GRAY™* Hood 25 is a particulate blocking hood designed to address this very issue. It helps to dramatically reduce the risks of carcinogenic particulate contamination while maintaining air permeability. Developed to meet the requirements of NFPA 1971, 2018 edition, the particulate blocking layer blocks carcinogenic particulates 0.1 µm to 1.0 µm that are found in the combustion of structural fires by greater than 98%. Yet, that same layer also allows for air permeation, which is essential to reduce the risk of increased core temperature. Available in Medium/Large (Most Common Size) or XL
800-558-8009
